Spindle moulders with tiltable spindle

Description

- new -
manufactured by Hofmann
type UFM 210 VISION
- Heavily ribbed cast iron table , finely sliced ??, with extendable support
- Sliding table with automatic. Depth adjustment , table slide adjustment to
any tool possible
- Interchangeable table insert , made ??of aluminum with hard-coat coating ,
for tools up to 160 mm and D of D 160 to D 250 mm
- The spindle taper MT 5 , arbor D 30 mm mounting length 125 mm
- Electrical height adjustment , vertical stand
( thus no correction of the depth adjustment with tilted spindle)
about 190 mm ??in the rapid and creep speed , display accurate to 0.1 mm
- Electric tilt adjustment from -45.5 ° to 95.5 ° in the fast and slow transition ,
Display to 0.1 °
- Electric milling depth ( stop remains fixed on the machine table ,
The adjustment is done by the milling spindle ) in the fast and slow transition ,
Display accurate to 0.1 mm , as well as no longer necessary correction of the advance
- Variable speed control from 1,500 to 10,000 rpm direct drive
- Speed ??selection by tapping the stored 10 speeds or variable
Typing on keyboard - without changing belts
- Pushbutton circuit for automatic start and stop the spindle
- Double-sided swivel storage unit in strong journal bearing , with
automatic . Clamping of the swivel angle
- Double-sided linear bearing for cutting depth and Routing height adjuster
- Adjustable fence fixed on the machine table , infeed jaw adjustment to
Digital Filter counter to the nearest 0.1 mm, adjustable from the operator side ;
Iron fence stop every 500 /500 mm
- Operating hours counter with hour meter order . Machine socket for
Feeder , control buttons on the console
- Blockage electric spindle , machine maintenance, HOFMANN milling guard " Centrex "
- 3 120 mm diameter suction stop at and below the table;
Minimum air flow 20 m³ / min . pa for 378
- Forward via two-hand operation with warning indicator
- Electrical equipment according to VDE / EN 60204 with main switch , emergency stop button,
Motor protection switch and coil protection , undervoltage protection , contact the
Controlling the exhaust, brake. Programming protection over key switch ,
serial interface for reading out the data
- Accessories: operating tools, operator manual
- CE-compliant
- BG- wood dust test No. 031 042

Specifications:
Table width 820 mm
Table length 1625 mm *
Table height 900 mm
Opening table use D to 250 mm
Swivel range - 45.5 ° to 95.5 °
Spindle taper MT5 * / HSK- F63 / HSK -F80
Spindle D * 30 mm
Useable * 125 mm
Spindle height adjustment up to 190 mm
Height adjustment function tripod 155-175 mm
Motor power 7.5 kW ** (direct drive)
Speeds 1500-10000 r / min. (infinitely )
Suction (3x ) D 120 mm
Minimum air flow 1200 m3 / h
1400 kg
Total depth approximately 1357 mm

* Information in the standard , expandable

Through ** direct drive significantly more torque on the spindle compared
to belt drives , high- FU allows S6 - which grants
continuous operation with intermittent load with a power of 10.5 kW

ex works

- new -
manufactured by Hofmann
type UFM 210 VISION
- Heavily ribbed cast iron table , finely sliced ??, with extendable support
- Sliding table with automatic. Depth adjustment , table slide adjustment to
any tool possible
- Interchangeable table insert , made ??of aluminum with hard-coat coating ,
for tools up to 160 mm and D of D 160 to D 250 mm
- The spindle taper MT 5 , arbor D 30 mm mounting length 125 mm
- Electrical height adjustment , vertical stand
( thus no correction of the depth adjustment with tilted spindle)
about 190 mm ??in the rapid and creep speed , display accurate to 0.1 mm
- Electric tilt adjustment from -45.5 ° to 95.5 ° in the fast and slow transition ,
Display to 0.1 °
- Electric milling depth ( stop remains fixed on the machine table ,
The adjustment is done by the milling spindle ) in the fast and slow transition ,
Display accurate to 0.1 mm , as well as no longer necessary correction of the advance
- Variable speed control from 1,500 to 10,000 rpm direct drive
- Speed ??selection by tapping the stored 10 speeds or variable
Typing on keyboard - without changing belts
- Pushbutton circuit for automatic start and stop the spindle
- Double-sided swivel storage unit in strong journal bearing , with
automatic . Clamping of the swivel angle
- Double-sided linear bearing for cutting depth and Routing height adjuster
- Adjustable fence fixed on the machine table , infeed jaw adjustment to
Digital Filter counter to the nearest 0.1 mm, adjustable from the operator side ;
Iron fence stop every 500 /500 mm
- Operating hours counter with hour meter order . Machine socket for
Feeder , control buttons on the console
- Blockage electric spindle , machine maintenance, HOFMANN milling guard " Centrex "
- 3 120 mm diameter suction stop at and below the table;
Minimum air flow 20 m³ / min . pa for 378
- Forward via two-hand operation with warning indicator
- Electrical equipment according to VDE / EN 60204 with main switch , emergency stop button,
Motor protection switch and coil protection , undervoltage protection , contact the
Controlling the exhaust, brake. Programming protection over key switch ,
serial interface for reading out the data
- Accessories: operating tools, operator manual
- CE-compliant
- BG- wood dust test No. 031 042

Specifications:
Table width 820 mm
Table length 1625 mm *
Table height 900 mm
Opening table use D to 250 mm
Swivel range - 45.5 ° to 95.5 °
Spindle taper MT5 * / HSK- F63 / HSK -F80
Spindle D * 30 mm
Useable * 125 mm
Spindle height adjustment up to 190 mm
Height adjustment function tripod 155-175 mm
Motor power 7.5 kW ** (direct drive)
Speeds 1500-10000 r / min. (infinitely )
Suction (3x ) D 120 mm
Minimum air flow 1200 m3 / h
1400 kg
Total depth approximately 1357 mm

* Information in the standard , expandable

Through ** direct drive significantly more torque on the spindle compared
to belt drives , high- FU allows S6 - which grants
continuous operation with intermittent load with a power of 10.5 kW

ex works